No Products in the Cart
Position desired color(s) of Deco Foil over adhesives. Press with iron following Deco Foil’s directions or place fabric and Deco Foil between parchment paper and run through laminator following your machine’s directions. It's important to be patient and let it cool completely. Gently rub over foiled area with a soft fabric to loosen the foil. Carefully remove foil and you're ready to sew.
Before you start sewing the bag together, machine or hand embroider lines on the air balloon. I used HeatnBond Transfer Sheets for the quote, but you could hand embroider the lettering on it.
Sewing instructions:
Step #1: Lay Piece #1 right side down on flat surface. Lightly spray wrong side of Piece #1 with Spray N Bond Basting Adhesive. Carefully lay Piece #4 (fleece or batting) on top of sprayed fabric. Smooth and reposition if necessary to remove creases or wrinkles.
Step #2: Sew Piece #2 to Piece #3, right sides together, lengthwise, with ¼” seams. Press seams toward Piece #3. *Be careful not to touch the Deco Foil and/or transfer when pressing!
Step #3: Spray fleece/batting with Spray N Bond Basting Adhesive. Lay sewn Pieces #2 and #3, wrong side down, on to sprayed fleece. Smooth to remove creases and wrinkles.
You should have a sandwiched piece with right sides showing on both sides. If desired, you can do additional quilting designs on this piece before continuing. Straight line quilting works great for this.
Step #4: Cut in half and trim edges to square it up. Make sure both pieces are the same size.
Step #5: Fold Piece #5 in half and press. Fold in lengthwise sides and press. Fold in half lengthwise to create narrow strip with no raw edges showing. Cut strip in half to make two pieces.
Step #6: Cut end off zipper (not pull tab end) to make the zipper 1” shorter than bag. Slide zipper ends in between folds of cut tab strip. Sew across folded end to secure tab to zipper. Make sure it catches both sides of fabric tab.
Step #7: Slide the second tab strip over the end of the pull tab side of zipper, pushing tabs together before sewing. Sew across folded end to secure tab to zipper. Check to make sure your stiches caught both sides of fabric tab. Trim tabs to same size as zipper.
Step #8: Lay the zipper face down on the right side of one Piece #2. Center zipper (it will be 1/2” in from both edges.) Sew close to the zipper teeth. As you reach the end near the pull tab, lift presser foot and open the zipper to enable sewing. Fold back Piece #2 and press on right side. Sew the other Piece #2 to the wrong side of the zipper just as you did on the other side. Open and press. Stitch a 1/4” along seam lines on both sides of zipper.
Step #9: A really important thing to remember for this step is to unzip the zipper before sewing. If you don’t, you won’t be able to turn the bag inside out (this MAYBE happened to me and it MIGHT have been no fun ripping out seams!) Once the zipper is unzipped, fold right sides together matching seams. Sew around the three edges (not the zipper side) with a 1/2” seam. Finish raw edges with a zig-zag stitch or serger.
Step #10: Turn bag inside out. Press edges being careful not to touch Deco Foil and/or transfer with hot iron. Load the bag with items that would be needed by a college-bound student like pot holders, towels, can opener, and other kitchen items.
Including a first aid kit (pattern found on my Craftsy page HERE) would be a sweet idea, too! It's sewn with the same directions of the All Zipped Up Bag, just smaller (5 1/2" x 8 1/2".)
Another fun thing about this bag is that once the goodies you included are removed by the graduate, it makes a great computer bag.
Ready to make your own zippered bag? You can find the PDF pattern for the All Zipped Up Bag at my Craftsy store HERE that will include the hot air balloon and lettering graphics. ~ Carol Swift
