Therm O Web Deco Foil Hot Melt Transfer Adhesive Sheets 3370
Therm O Web Deco Foil Hot Melt Transfer Adhesive Sheets 3370
  • SKU: 3370
  • Availability: in stock Many in stock Out of stock You can purchase this product but it's out of stock

Deco Foil Hot Melt Transfer Adhesive Sheets

$4.99
  • Barcode: 000943033707
Deco Foil Hot Melt Adhesive is a hot melt adhesive perfect for wearables, cards and so much more. This adhesive is also washable on fabric projects. Use Deco Foil Hot Melt Adhesive in punches, die cutters and electronic cutters. Deco Foil Hot Melt Adhesive also works great in most laminators

Product Details

  • 5.5 inches x 12 inches
  • 5 Sheets per pack
  • Acid Free
  • Use with: punches, die cutter and electronic cutters
  • Exclusively use with any of our Foil Transfer Sheets
  • Proudly made in the USA

Video

Directions for Paper Crafts

  1. Create a design using a punch, die-cutting machine, or electronic cutter from the Hot Melt Adhesive sheet. Note: If used with a die-cutter or punch, cover the adhesive (rough side) with parchment paper (included) prior to cutting or punching. For electronic cutters, place adhesive (rough side) face up. Be aware of orientation when using a die-cutter or electronic cutter, design may need to be cut in a mirror image.
  2. Place design onto project with adhesive (rough side) face down. Place project inside the folded parchment paper.
  3. Turn on laminator, select 5 mil setting, and allow 5 minutes to warm up. When ready, insert folded parchment with project into laminator using the crease as the lead edge.
  4. Remove project from parchment paper and allow to cool. Peel off liner to expose adhesive design.
  5. Cut a piece of foil slightly larger than the design. Place foil. color side facing us, on top of the adhesive design.
  6. Using the same folded parchment paper, place project with foil-covered adhesive design inside.
  7. Insert into laminator using the crease as the lead edge.
  8. Remove project from parchment paper and allow to cool.
  9. Peel foil transfer sheet away from adhesive design.

Directions for Fabric Crafts

  1. Create a design using a punch, die-cutting machine, or electronic cutter from the Hot Melt Adhesive sheet. Note: if used with a die-cutter or punch, cover the adhesive (rough side) with parchment paper (included) prior to cutting or punching. For electronic cutters, place adhesive (rough side) face up. Be aware of orientation when using a die-cutter or electronic cutter, design may need to be cut in a mirror image.
  2. Place design onto project with adhesive (rough side) face down and cover with parchment paper (included).
  3. Pre-heat iron to a medium setting, no steam. Place and hold iron on the parchment paper with adhesive design underneath for 30 seconds. Repeat until entire surface is bonded.
  4. Remove parchment paper and allow to cool. Peel off liner from design.
  5. Cut a piece of foil slightly larger than the design. Place foil, color side facing up, on top of the adhesive design and place a piece of parchment paper over the foil.
  6. Iron the project slowly with firm pressure for 30-40 seconds. When completely, remove parchment paper and allow to cool.
  7. Peel foil transfer sheet away from adhesive design.
  8. Washing instructions: Hand wash and lay flat to dry. If needed, machine wash on cold, delicate cycle. Do not iron foiled areas.

Tips

  • Always pre-test for best results.
  • Directions are based on Royal Sovereign # CS923/1223. Other brands/models' temperature and speed settings may vary.
BACK TO TOP